Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
What are your beliefs about How to Install a Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a reasonably challenging job. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open up a wall to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the work and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to think about utilizing one prior to you start. Chances are you might need a specialist plumber to make tube links.
This article will aid you install a brand-new tub in your shower room if you have currently purchased a brand-new bathtub and don't need to change the arrangement of your previous supply of water pipes.
Your devices and also material list must make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is separate the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather bothersome as a result of the limited gain access to that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the tap and the sink. Protect the tap in place with the manufacturer provided backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal tap ports. The previous kind must be linked to the tap ends initially, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Installing the Bathtub
Making use of both wooden boards under its feet, position the tub in the needed placement. The wooden boards are useful in equally spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by checking the spirit level as well as adjusting the feet on the bathtub till the spirit level checks out degree.
To mount taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and check all joints and also new pipework for leaks and tighten them if needed. Fill up the tub and also check the overflow outlet and also the typical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub needs to wait till the bath tub has actually been used a minimum of once as this will certainly resolve it into its final setting.
Planning for the Installment
Firstly, the sustaining structure supplied with the bath must be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, triggering the water to pass through the wall surface between the bathroom and also the tiling, resulting in problems with moisture and feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can split rather very early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark down the page. We will be glad to hear your opinion about this blog post. We are looking forward that you come back again later on. So long as you enjoyed our post if you please do not forget to pass it around. Many thanks for your time. Visit us again soon.
Ensure plumbing integrity; reach out. Report this page